|
CE Marking Directive Compliance
|
EMC Directive, RoHS Directive
|
|
Supply Voltage
|
12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
|
|
Power Consumption
|
Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage)
ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage)
|
|
Output
|
NPN open-collector transistor
- Maximum sink current: 100 mA
- Applied voltage: 30 V DC or less (between output and 0 V)
- Residual voltage: 1.5 V or less (at 100 mA sink current)
|
|
Output: Output Operation
|
Selectable either Light-ON or Dark-ON, at SET mode
|
|
Output: Short-Circuit Protection
|
Incorporated
|
|
External Input
|
NPN non-contact input
- Signal condition
High: +8 V to +V DC or Open
Low: 0 to +2 V DC(Source current 0.5 mA or less)
- Input impedance: 10 kOhm approx.
|
|
Response Time
|
Emission frequency 1: 2.5 ms or less (factory default setting)
Emission frequency 2: 2.8 ms or less
Emission frequency 3: 3.2 ms or less
Emission frequency 4: 5.0 ms or less
|
|
Sensitivity Setting
|
2-point teaching / Limit teaching / Full-auto teaching
|
|
Operation Indicator
|
Orange LED (lights up when the output is ON)
|
|
Digital Display
|
4 digits (green) + 4 digits (red) LCD display
|
|
Fine Sensitivity Adjustment Function
|
Incorporated
|
|
Timer Function
|
ON-delay / OFF-delay timer, switchable either effective or ineffective
[Timer period: 1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms]
|
|
Emission Amount Setting Function
|
3-level + Auto setting (from production in December 2007)
|
|
Interference Prevention Function
|
Incorporated Emission frequency selection method (Functions at emission frequency 1, 2, 3 or 4)
(Note) When using the interference prevention function, set the emission frequencies for the amplifiers to be covered by the interference prevention function to different frequency values.
|
|
Ambient Temperature
|
–10 to +55 ℃ +14 to +131 ℉
(If 4 to 7 units are mounted close together: –10 to +50 ℃ +14 to +122 ℉, if 8 to 16 units are mounted close together: –10 to +45 ℃ +14 to +113 ℉) (No dew condensation or icing allowed),
Storage: –20 to +70 ℃ –4 to +158 ℉
|
|
Ambient Humidity
|
35 to 85 % RH, Storage: 35 to 85 % RH
|
|
Ambient Illuminance
|
Incandescent light: 3,000 lx or less at the light-receiving face
|
|
Voltage Withstandability
|
1,000 V AC for one min. between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
|
|
Insulation Resistance
|
20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
(Note) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
|
|
Vibration Resistance
|
10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
|
|
Shock Resistance
|
98 m/s2 acceleration (10 G approx.) in X, Y and Z directions five times each
|
|
Emitting Element (Modulated)
|
Red LED (Peak emission wavelength: 643 nm 0.025 mil)
|
|
Material
|
Enclosure: Polycarbonate
Key switch: Polycarbonate
Fiber lock lever: PBT
|
|
Connecting Method
|
Connector
(Note) Connector attached cable CN-14A-C2 is not attached to the models that have no ''-CC2'' at the end of the model Nos.Make sure to use the optional connector attached cable CN-14A(-R)-Cx or the connector CN-14A, or a connector manufactured by J.S.T. Mfg., Ltd.(contact: SPHD-001T-P0.5, housing: PAP-04V-S).
|
|
Cable Length
|
Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
|
|
Weight (Typ.)
|
Net weight: 15 g approx.
Gross weight: 35 g approx.
|
|
Accessory
|
FC-FX-1(Protection cover): 1 pc.
(Note) Protection cover FC-FX-1 has been attached from the production at July, 2011.
|
